Kurum Yazarı "Kara, Ferhat" Seramik Mühendisliği İçin Listeleme
-
Hydrated aluminium sulfate precipitation by enzyme-catalysed urea decomposition
Kara, Ferhat; Şahin, G (Elsevier Sci LTD, 2000)Hydrated basic aluminium hydroxide precipitates were obtained from aluminium sulphate solution at room temperature and at 92 degrees C by using urea. Enzyme urease was used to decompose urea at room temperature. It was ... -
Improvement of sintering and microstructural homogeneity of a diphasic mullite
Kara, Ferhat; Şener, O (Elsevier Sci LTD, 2001)Effect of seeding of boehmite-colloidal silica mixture with aluminium sulphate-colloidal silica mixture on its mullite formation and sintering behaviours and microstructural development was studied. It was observed that ... -
Mechanical properties of melt infiltrated boron carbide-aluminium composites
Arslan, Gökhan; Kara, Ferhat; Turan, Servet (Trans Tech Publications LTD, 2002)Boron carbide (B4C)-aluminium (Al) composites were produced by melt infiltration of 2024-T3 series Al alloys into porous B4C compacts in the temperature range of 985 degrees -1370 degreesC under an inert atmosphere (Ar). ... -
Microstructural characterisation of melt infiltrated boron carbide-aluminium composites
Arslan, Gökhan; Kara, Ferhat; Turan, Servet (IOP Publishing LTD, 2001)The microstructure of boron carbide (B4C) - aluminium (Al) composites produced by reactive infiltration were characterised using a scanning electron microscope (SEM) and a transmission electron microscope (TEM) both attached ... -
Microstructural characterization of reactively sintered mullites
Kara, Ferhat; Turan, Servet; Little, JA; Knowles, KM (Amer Ceramic Soc, 2000)Mullite ceramics have been produced by reaction sintering of powders prepared using pseudoboehmite-colloidal silica and aluminum sulfate-colloidal silica mixtures. The microstructural development of these mullites was ... -
Microstructural characterization of surface layers formed on a low alloy steel during erosion - oxidation in a fluidized bed
Rogers, PM; Hutchings, IM; Little, JA; Kara, Ferhat (Chapman Hall LTD, 1997)Low alloy steel specimens were subjected to erosion-oxidation in a simulated fluidized bed environ ment in the range 100-600 degrees C. Transmission electron microscopy was carried out on the surfaces which experienced ... -
Novel SiAlON ceramics for cutting tool applications
Mandal, Hasan; Kara, Ferhat; Turan, Servet; Kara, Alpagut (Trans Tech Publications LTD, 2003)New alpha-beta SiAlON ceramics were produced in aqueous medium by Using Multiple oxides as densifying additives. The sintered materials were characterised using a combinations of techniques such as XRD, SEM and TEM. The ... -
Performance of new ?-ß SiAlONs in turning operations
Mandal, Hasan; Kara, Ferhat; Turan, Servet; Kara, Alpagut (2001)New ?-ß SiAlON ceramics were produced, characterised and tested in turning operations of cast iron. Cutting speeds varied between 400-1200 m/min while feeding rates were between 0.3 to 0.5 mm/rev. The results were compared ... -
Performance of new alpha-beta SiAlONs in turning operations
Mandal, Hasan; Kara, Ferhat; Turan, Servet; Kara, Alpagut (Trans Tech Publications LTD, 2002)New alpha-beta SiAlON ceramics were produced, characterised and tested in turning operations of cast iron. Cutting speeds varied between 400-1200 m/min while feeding rates were between 0.3 to 0.5 mm/rev. The results were ... -
Phase studies of reactive infiltrated boron carbide-aluminium composites by quantitative XRD
Arslan, Gökhan; Kara, Ferhat; Turan, Servet (Trans Tech Publications LTD, 2002)Fully dense (> 98 % of theoretical) boron carbide (B4C)-aluminium (Al) composites were produced between 985 degrees and 1370 degreesC by pressureless melt infiltration of Al alloys into porous B4C compacts under an argon ... -
Seramik sanayii hızlı pişirim fırınlarda kullanılanan rulo malzemesi müllitin üretimi ve mekanik özelliklerinin belirlenmesi
Yorulmaz, S.; Erkmen, Engin Ziya; Kara, Ferhat (Scientific and Technical Research Council of Turkey, Ankara, Turkey, 1999)A mullite matrix ceramic was developed for use as the roller material in fast fire kilns. Samples of the mullite ceramic were produced from mixtures of domestic ?-Al2O3 and kaolin clay through conventional methods of ceramic ... -
Transmission electron microscopy of SrO containing multi-cation doped ?-SiAlON ceramics
Turan, Servet; Mandal, Hasan; Kara, Ferhat (2002)An advantage of ?-SiAlON is that it can accommodate cations of sintering additives and hence reduces the amount of deleterious remnant intergranular amorphous phase. However, it is believed that relatively large cations ... -
Transmission electron microscopy of SrO containing multi-cation doped alpha-SiAlON ceramics
Turan, Servet; Mandal, Hasan; Kara, Ferhat (Trans Tech Publications LTD, 2002)An advantage of alpha-SiAlON is that it can accommodate cations of sintering additives and hence reduces the amount of deleterious remnant intergranular amorphous phase. However, it is believed that relatively large cations ... -
Transmission electron microscopy studies of La2O3-doped alpha-SiAlON ceramics
Turan, Servet; Mandal, Hasan; Kara, Ferhat; Knowles, KM (IOP Publishing LTD, 1999)alpha-SiAlON is able to accommodate cations into its crystal structure if the cations are sufficiently small in size, thus helping to reduce the volume of the remnant grain boundary phase after processing. In this study, ...