Başlık için Malzeme Bilimi ve Mühendisliği Bölümü listeleme
Toplam kayıt 444, listelenen: 198-217
-
Interactions between a bismuth type leadless glaze and a bone China body during glost firing
(Trans Tech Publications LTD, 2004)In the present study, the interactions between a high bismuth type commercial transparent leadless glaze and a biscuit fired bone china body during glost firing at different temperatures were investigated using SEM. The ... -
Interactions between a leadless glaze and a biscuit fired bone China body during glost firing - part III: effect of glassy matrix phase
(Elsevier Sci LTD, 2003)As the final part of the study, the interactions between a commercial leadless glaze and a simulated bone china body glass during glost firing at different temperatures have been investigated. Advanced techniques such as ... -
Interactions Between AlN and SiAlON Ceramics
(Trans Tech Publications LTD, 2009)In the present study, interactions between AlN and SiAlON laminated couples were investigated after gas pressure (GPS) and spark plasma sintering (SPS) by scanning electron microscopy (SEM) and energy dispersive x-ray ... -
Interface roughness and exchange bias - Coercivity ratio in Pulsed-DC magnetron sputtered NiFe/IrMn/CoFe exchange bias trilayers
(2013)Ta/Ru/Ta/Ni81Fe19/Ir20Mn 80/Co90Fe10 exchange bias multilayer was grown by using pulsed DC unbalanced magnetron sputtering technique. The deposition pulse frequency of the NiFe seed layer has been varied between 10 - 50 ... -
An investigation into bloating behaviour of bone China body during biscuit firing
(Trans Tech Publications LTD, 2004)Amongst many studies on the textural, mineralogical and physical changes during biscuit firing of whiteware bodies, this paper attempts to investigate the bloating behaviour of a commercial bone china body during biscuit ... -
Investigation of borax waste behaviour in tile production
(Elsevier Sci LTD, 2007)Although there are various studies published in the relevant literature on the use of borates in tile production, borax waste has been mainly used in place of feldspar and the results showed that borate migration to the ... -
An investigation of Hellenistic period pottery production technology from Harabebezikan/Turkey
(Elsevier Sci LTD, 2011)Upper ancient Mesopotamia is a part of Southeastern Anatolia and irrigated by the Euphrates and Tigris rivers. It has several sites, ruins and monuments belonging to ancient civilizations. Among these, an ancient site ... -
Investigation of lead extraction process from galena concentrates by full factorial design
(Korza Matbaacilik, 2011)Nowadays the use of environment-friendly processes is gaining an increasing importance in metallurgy. Environmental regulations are continuously making it difficult to produce lead from galena concentrates by pyrometallurgical ... -
Investigation of parameters affecting formation of mullite from kaolin
(Trans Tech Publications LTD, 2004)This study aims to improve the understanding of formation of mullite from kaolin at low process temperature using different sintering regimes. The optimum parameters affecting mullite formation from kaolin such as sintering ... -
Investigation of parameters affecting grain growth of sintered magnesite refractories
(Elsevier Sci LTD, 2005)The parameters influencing grain size of sintered magnesite such as temperature (1700 and 1800degreesC), time (19 and 50 min), cooling rate (5, 10 and 25degreesC min(-1)) and various particle size (-3; +3,-5; +5,-8; +8,-10 ... -
Investigation of PM parameters' effect on architecture of titanium foams using X-ray microtomography
(European Powder Metallurgy Association (EPMA), 2010)Titanium foams have been of interest in dental and orthopedic implants over the past few decades on account of their excellent mechanical properties, chemical stability, and biocompatibility. In this study, titanium foams ... -
Investigation of porosity of ceramic tiles by means of image analysis method
(Korean Assoc Crystal Growth, Inc, 2014)Amount, size and distribution of porosity are among the important factors which affect physical and mechanical properties of ceramic tiles. In this study, the effect of flux variation in porcelain tile recipes and different ... -
An investigation of pottery production technology for the West Slope wares from Dorylaion (Eskisehir/Turkey)
(Soc Espanola Ceramica Vidrio, 2013)Researches in the field of pottery production technology in ancient times, done in different settlements during the same period, may contribute to know relationships established within the different cultural communities. ... -
Investigation of sanitaryware scrap behaviour in terracotta bodies
(Trans Tech Publications LTD, 2004)In this paper, an investigation into a potential use of unfired body scrap from a local sanitaryware manufacturer in commercial terracotta production was presented. Experiments were achieved under laboratory conditions by ... -
Investigation of spacer size effect on architecture and mechanical properties of porous titanium
(Elsevier Science Sa, 2011)Titanium and its alloy foams have been receiving a growing interest for biomedical industry due to their biocompatibility and high potential in dental, spinal, joint and hip implant applications. Near net shape production ... -
An investigation of the effect of alkaline oxides on porcelain tiles using factorial design
(Korean Assoc Crystal Growth, Inc, 2012)In this study, the effect of alkaline oxides (MgO, CaO, Na2O and K2O) was investigated in porcelain tile compositions. Talc (MgO) and dolomitic clay (CaO, MgO) were added to porcelain tile compositions instead of feldspar ... -
Investigation of the Improvements on Mechanical Properties and Thermal Performance of MgO-MgAl2O4 Composite Refractories by Additions of ZnO-Al2O3 to MgO
(Trans Tech Publications LTD, 2012)The variations and developments with the reasons on the mechanical properties of MgO-MgAl2O4 and MgO-ZnO-Al2O3 composite refractories were examined and thermal parameters affecting the durability of composites at high ... -
Investigation of the influence of initial powder size on the optical properties of Dy-alpha-SiAlON ceramics fabricated by gas pressure sintering
(Elsevier Sci LTD, 2017)Translucent Dy3+ doped alpha-SiAlON ceramics were successfully fabricated by the gas pressure sintering (GPS) method. The efficacy of this sintering technique also the affects initial particle size on densification, final ... -
Investigation of the Strength of Floor Tiles by Using An Experimental Design Method
(Australian Ceramic Society, 2015)The main objective of this work is to determine the main parameters affecting the strength properties of floor tiles. For this purpose, the effect of various ratios of the components in the Seger formulation on fast firing ... -
Investigation on the performance of SiAlON ceramic drills on aerospace grade CFRP composites
(Elsevier Science Sa, 2015)Carbon fiber reinforced polymer (CFRP) composites are widely used in aircraft structure due to their outstanding physical and mechanical properties. Drilling is one of the most critical operation in the handling of CFRP ...