Güncel Gönderiler: Makine Mühendisliği Bölümü
Toplam kayıt 57, listelenen: 41-57
-
Achieving Fast Kinetics and Enhanced Li Storage Capacity for Ti3C2O2 by Intercalation of Quinone Molecules
(American Chemical Society, 2019)Using first-principles calculations, we demonstrated that high lithium storage capacity and fast kinetics are achieved for Ti3C2O2 by preintercalating organic molecules. As a proof-of-concept, two different quinone molecules, ... -
Defining and comparing vibration attributes of AlSi10 foam and CFRP coated AlSi10 foam materials
(IOP Publishing LTD, 2017)Now, Aluminum materials have begun being manufactured as porous structures and being used with additive composite materials through emerging manufacturing technologies. These materials those porous structures have also ... -
Cutting Forces and 3D Surface Analysis of CFRP Milling with PCD Cutting Tools
(Elsevier Science BV, 2016)This paper provides a study on the milling of carbon fiber reinforced laminated composites. A set of milling experiments were carried out under various conditions. Cutting force results were measured and analyzed (based ... -
Real-time virtual clothes try-on system
(Inst Natl Cercetare-Dezvoltare Textile Pielarie-Bucuresti, 2016)Virtual clothes try-on has recently come into the researchers' focus owing to its commercial potential. It can be used as an efficient tool in online shopping, allowing users to narrow down their choices to a few designs ... -
Design, fabrication, and testing of a multiple-actuation shape memory alloy pipe coupler
(SAGE Publications LTD, 2018)Shape memory alloy pipe couplers use the shape memory effect to apply a contact pressure onto the surface of the pipes to be coupled. In the current research, a shape memory alloy pipe coupler is designed, fabricated, and ... -
Effect of grain refinement and phase composition on room temperature superplasticity and damping capacity of dual-phase Zn-Al alloys
(Cambridge University Press, 2018)The effects of grain refinement and phase composition on superplasticity and damping capacity of eutectic Zn-5Al and eutectoid Zn-22Al alloys were investigated. For grain refinement, equal-channel angular pressing (ECAP) ... -
Distributions of Compressive Strength Obtained from Various Diameter Cores
(Amer Concrete Inst, 2012)Test results from cores with diameters smaller than the standard sizes and with length-to-diameter (Vd) ratios less than I are considered to be unreliable due to higher variability in concrete strength. There is, however, ... -
Thermomechanical cyclic stability of porous NiTi shape memory alloy
(Pergamon-Elsevier Science LTD, 2017)It is known that shape memory and phase transition response of NiTi shape memory alloy (SMA) is dependent on mechanical or thermal background, and the presence of phases such as B2(NiTi), B19'(NiTi), Ni4Ti3, Ni3Ti2 and ... -
Enhancing the Damping Behavior of Dilute Zn-0.3Al Alloy by Equal Channel Angular Pressing
(Springer, 2017)The effect of grain size on the damping capacity of a dilute Zn-0.3Al alloy was investigated. It was found that there was a critical strain value (ae1 x 10(-4)) below and above which damping of Zn-0.3Al showed dynamic and ... -
Work production using the two-way shape memory effect in NiTi and a Ni-rich NiTiHf high-temperature shape memory alloy
(IOP Publishing LTD, 2015)The work output capacity of the two-way shape memory effect (TWSME) in a Ni50.3Ti29.7Hf20 (at%) high-temperature shape memory alloy (HTSMA) was investigated and compared to that of binary Ni49.9Ti50.1 (at%). TWSME was ... -
The effect of tensile deformation on the damping capacity of NiTi shape memory alloy
(Elsevier Science Sa, 2016)The vibration damping capacity of a near-equiatomic NiTi shape memory alloy was characterized as a function of tensile deformation by utilizing dynamic mechanical analysis. The intrinsic internal friction (IF) values of ... -
Influence of tantalum additions on the microstructure and shape memory response of Ti50.5Ni24.5Pd25 high-temperature shape memory alloy
(Elsevier Science Sa, 2014)A Ti50.5Ni24.5Pd25 (at%) high-temperature shape memory alloy (HTSMA) was alloyed with 1, 3, and 5 at% Ta additions in an effort to enhance the shape memory properties, particularly the dimensional stability for actuator ... -
The effect of dynamic aging on the cyclic stability of Cu73Al16Mn11 shape memory alloy
(Elsevier Science Sa, 2017)This study focuses on the effect of dynamic aging on the thermo-mechanical cyclic stability of Cu73Al16Mn11 (at %) shape memory alloy (SMA) during constant stress (isobaric) and stress-free heating-cooling experiments. ... -
Dose-dependent effect of radiation on resorbable blast material titanium implants: an experimental study in rabbits
(Taylor & Francis LTD, 2018)Background: Radiotherapy is a commonly used treatment modality in head and neck cancer; however, it also negatively affects healthy structures. Direct damage to oral soft and hard tissue frequently occurs with radiotherapy. ... -
Wear performance of different nitride-based coatings on plasma nitrided AISI M2 tool steel in dry and lubricated conditions
(Elsevier Science Sa, 2017)AISI M2 high speed tool steel is one of the widely used materials in the machining industry. The most common problems of this material are wearing of the cutting edge and adhesion of the work materials to the tool during ... -
Wear behavior of the plasma and thermal oxidized Ti-15Mo and Ti-6Al-4V alloys
(IOP Publishing LTD, 2017)Titanium and its alloys widely used in load bearing applications. Titanium alloys are capable of providing lower elastic modulus and better corrosion resistance with alloying processes. In spite of the modified mechanical ... -
Improvement the wear behavior of low carbon steels by friction stir processing
(IOP Publishing LTD, 2017)A low carbon structural steel was surface-hardened by friction stir processing (FSP) through 4 mm thickness from the surface. The hardness of the alloy increased from 140 Hv0.1 to about 240 Hv0.1 after single-pass FSP. ...
